Wet cooling is predominantly used in thermoelectric power plants for condensing steam from the turbine owing to their low system cost and for their ability to render lower turbine back pressure (in comparison to dry cooling). However, the implementation of wet cooling in arid regions is costly while implementation of dry cooling in arid regions can degrade operational reliability (while also increasing both capital costs and operational costs). As a result, alternate technologies are needed to wean power plants from using fresh water resources while also enhancing the operational reliability of dry cooling. Air cooled heat exchangers installed in arid climates are inoperable on certain days during summer as the ambient air temperature can exceed the temperature of the steam at the turbine exhaust and may lead to power plant shutdown, in-turn, causing instability in the electric supply grid infrastructure (thus compromising reliability). In order to combat these shortcomings, supplemental cooling options may be needed. Thermal Energy Storage (TES) platforms can provide an attractive option for supplemental cooling. Phase Change Materials (PCM) are often used as viable options for Latent Heat Thermal Energy Storage Systems (LHTESS) as they have small footprint owing to the high latent heat values of PCM.

The objective of this study is to analyze the performance of various LHTESS platforms by utilizing different configurations of the Heat Exchangers (HX) that are filled with PCM. The scope of this study is limited to using an organic Phase Change Material (PCM) and two different HX configurations are explored in this study: (a) a Shell and Tube Heat Exchanger that was fabricated using Advanced Manufacturing (AM) technique (i.e., “3D Printing”); and (b) a conventional Chevron Plate Heat Exchanger (PHX) that was procured commercially from a vendor. The thermal response and performance characteristics (e.g., power rating and HX effectiveness) of the two HX configurations are measured experimentally in order to ascertain their efficacy for melting and solidification of the PCM for different flow rates and inlet temperature values of the working fluid. The working fluid is called the Heat Transfer Fluid (HTF). The HTF used in this study is tap water. The PCM used in this study is PureTemp 29 (commercially procured from Pure Temp Inc., Minneapolis, MN).

The propagation of the melt and the freeze fronts were monitored and tracked based on the nature of the transient temperature profiles recorded by an array of thermocouples. The array of thermocouples were strategically mounted at different locations within the HX containing the PCM. For the 3D-Printed HX (Shell and Tube HX), the thermocouples were located at different radial and axial locations within the shell containing the PCM. For the PHX, the thermocouples were located at different heights (for different plates containing the PCM).  The transient values of the power and capacity ratings for the HX were estimated based on the time-history of the transient values of the temperature differential for the bulk temperature of the HTF flowing between inlet and outlet ports of the HX (and this was correlated with the transient profile and location as well as the propagation of the solid-liquid interface within the HX). 

The performance characteristics of both HX, analyzed from the experimental data, show that the average power rating for the melting-cycle is consistently higher than that of the solidification-cycle due to the dominance of free convection during melting (resulting in higher values of the effective heat transfer coefficients for the same temperature differential values); while the solidification process is dominated by transient conduction (resulting in lower values of the effective heat transfer coefficients for the same temperature differential values).


Comparison of Thermal Performance of 3 D Printed Shell and Tube Heat Exchanger With Commercial Plate Heat Exchanger for Thermal Energy Storage (Tes) by Incorporating Phase Change Materials (Pcm)

Division / Sponsors: 
Heat Transfer Division (HTD), Fluids Engineering Division (FED)

Heat Transfer Summer Conference
Paper Proceedings: https://asmedigitalcollection.asme.org/HT/HT2020/volume/83709

18th International Conference on Nanochannels, Microchannels, and Minichannels
Paper Proceedings: https://asmedigitalcollection.asme.org/ICNMM/ICNMM2020/volume/83693

Fluids Engineering Division Summer Meeting
Paper Proceedings: https://asmedigitalcollection.asme.org/FEDSM/FEDSM2020/volume/83716

HT-ICNMM2020 - Virtual Conference, SHTC - Virtual Conference, FEDSM2020 - Virtual Conference

Supporting the need among researchers worldwide for additional online and multimedia content, ASME now offers the ASME Conference Video Collection. This platform will collect and provide long-term access to conference presentation videos, encompassing all technology areas within ASME's technical conference and events program. About 30,000-40,000 engineers across all mechanical engineering and related disciplines participate in ASME conferences each year. This includes authors of approximately 6,000 to 8,000 technical papers published by ASME, the majority of whom also submit video presentations for our virtual conferences. The video collection will be available as an add-on to existing product packages or as a separate subscription.